I need some help with my D7100. I am trying to do HDR photography and they say to bracket using EV (exposure value). They say bracket 2EV. But when I check bracketing in my D7100 user manual they say 1/2 or 1/3 value. I don't understand the connection. What am I doing wrong?
Thanks in advance,
#2. "RE: Bracketing" | In response to Reply # 1Mon 15-Jul-13 05:32 PM | edited Mon 15-Jul-13 05:37 PM by Bela614
I am still confused. I must be dense. The users manual was the first thing I checked.
#4. "RE: Bracketing" | In response to Reply # 3mklass Nikonian since 08th Dec 2006Mon 15-Jul-13 06:17 PM | edited Mon 15-Jul-13 06:22 PM by mklass
You need to set 2 things for HDR Bracketing on the D7100:
- Set the number of shots in the bracket: press and hold the bracket button on the left front of the camera (below the flash button and above the lens release button) and rotate the primary (rear, unless you've changed it) command dial to the desired bracket set: 3, 5 or -2, -3, +2, +3. (3 takes the base shot plus one above and another below the base exposure. 5 takes 2 above and 2 below. The + and - settings should be self explanatory).
- Set the exposure increment of the bracket: press and hold the bracket button and adjust the secondary (front) command dial to set the difference between the exposures. Choices are 0.3, 0.7, 1, 2 and 3).
If you don't already know:
- shoot in aperture priority or manual mode
- if you have set any exposure compensation, it will effect the base image and the starting point of the bracketing adjustments.
- to avoid pressing the shutter release for each bracket shot, set the mode to Cl or Ch, hold the shutter until the camera stops firing, which should happen after the number of selected bracket shots. Even better, use a tripod and cable release.
If you are attempting to use the in-camera HDR feature, you must be shooting JPG and the camera takes 2 images and combines them. You can set the level of range between low and extra high, or Automatic. You don't have much control over the results.
Hope that helps.
Visit my nikonians gallery
#5. "RE: Bracketing" | In response to Reply # 0
When bracketing, you need to pick:
- number of frames
- EV difference between the frames
While holding in the bracket button:
The main/back command dial picks the number of frames.
The sub/front command dial picks the EV difference between the frames.
The Custom Setting B2 controls the available EV steps when using steps less than a whole step.
Seattle, WA, USA
D700, D200, D70S, 24-70mm f/2.8, VR 70-200mm f/2.8 II,
50mm f/1.4 D, 70-300mm f/4.5-5.6 VR, 18-70mm f/3.5-4.5 DX
#6. "RE: Bracketing" | In response to Reply # 0
Bill you are confusing two different things. Menu item b2 is for your EV composition amount when you need to go plus or minus some EV value to properly expose an image using the top EV button and the command dial(rear dial).
For HDR,I take a picture,check the Histogram for proper exposure,when the Histogram is where I think it needs to be I then cover the lens with my hand to get a blank image so I know where the series starts and then
(1) push and hold in the bracket button
(2) while holding in bracket button,rotate sub-command dial(front dial)to set EV spread-I use 1.0 or 2.0
(3) still holding in bracketing button,rotate command dial(rear dial) to get the number of images you will need for a good HDR image(I use 3 or 5 depending on the scene)
If you use CL or CH and a wired cable release then just press and hold the button until all images are taken and the camera will stop when the series is complete. When done you must reset the dial for number of shots back to zero or you will remain in bracketing mode.
#7. "RE: Bracketing" | In response to Reply # 0
As far as the D7100 goes, bracketing and the HDR function are two different things. The simple HDR function takes two photos at different exposures and produces a single photo with increased dynamic range. It then writes this single photo to your memory card.
Bracketing allows you to take a number of photos at different exposures. It does not combine these photos in camera. It allows you to do a few different things with the bracketing photos such as choose the correct exposure from the group to get the best one. Or you can use HDR software which combine all the photos together to get a unique look in the end result single photo.
HDR in camera is not that sophisticated whereas HDR photos from software is quite sophisticated and allows you to fine tune the final photo.
So the two pages mentioned in the above posts are actually defining two different processes.
Visit my Nikonians gallery.
#8. "RE: Bracketing" | In response to Reply # 7Tue 16-Jul-13 10:00 AM
Thank you all for your help. I now have the camera set properly. But I am still confused about one thing. In the "Custom Setting Menu" under "B" metering exposure I have two choices, 1/3 step or 1/2 step. What is this for?
Thanks in advance,
#9. "RE: Bracketing" | In response to Reply # 8elec164 Nikonian since 15th Jan 2009Tue 16-Jul-13 10:55 AM
It allows you to choose the metering steps between one-half stops or one-third stops.
Set it to 1/2 and you'll get shutter speed and aperture choices in 1/2 stops such as shutter speeds of 1/30, 1/45, 1/60....etc
Set it to 1/3 and shutter speed choices would be 1/30, 1/40, 1/50, 1/60...etc.
The same applies to aperture.
1/2-stops--- f/2.8, f/3.3, f/4...etc.
1/3-stops--- f/2.8, f/3.2, f3.5, f4...etc.
Visit my Nikonians gallery.