Nikon D7000 - to use a Flash - SB28:
I have recently purchased a Nikon D7000 and am reall1y enjoying my learning experience with my first digital SLR.
My late father was a film camera Nikon collector and I have retained a flash unit, the Nikon Speed-light - SB28.
I have been told its a good flash unit, and that I can use it on the D7000 in manual mode.
How is this done, where can I go to get some information on how to run this flash unit manually?
I am not an experienced camera operator, coming through the film era with compact and fixed lens film camera's, onto the fixed lens digital cameras.
I have purchased the D7000 because of its reviews, and I am able to use a couple of lenses from my fathers collection (AF Nikkor 24-120, and 70-300 mm lenes.
I will appreciate any advise given.
#1. "RE: Nikon D7000 - to use a Flash - SB28:" | In response to Reply # 0Patrick604 Nikonian since 24th Jun 2012Wed 09-Jan-13 09:59 PM
A quick and easy way to get your exposure is to use the guide number, distance and f/stop method.
The guide number of that flash is roughly 110 ft at ISO 100 at 35 mm setting. Divide the guide number by the distance between the flash and the camera for the correct f/stop.
For example, you are taking a picture of a person who is 15 feet away from the flash (not the camera unless the flash is on the camera). Divide 110/15 = 7.3. Your correct f/stop will then be f/7.3 or you can round up to f/8.
Take a picture and review your shot/histogram and adjust your f/stop as needed.
You can rework the equation to fit the situation. If you want to shoot at a particular f/stop, and you know the guide number, then you can calculate how far away your flash should be as follows: d=GN/f. So if you wanted to use the GN 110, and you want to shoot at f/8, you should place your camera 13.75 feet away from your subject because d=110/8=13.75.
The thing you need to remember, is that the GN of your flash changes based on the zoom head setting of the flash. The 110 ft GN is good for 35 MM, but the GN will be higher if your flash is set to 50mm or 85 mm. You can look these figures up online by conducting a search for SB-28 guide number, and create a little chart you can print on an index card and keep in your kit.
Something to keep in mind is that this does not need to be precise. If I am in the field and have to shoot in manual mode, I tend to ballpark the math. In other words, I would use f/8 instead of f/7.3, and I would use 15 feet instead of 13.75 as calculated above. You just need to get it close, then review your image and histogram and make any fine adjustments you deem necessary.
Of course, if you want to cheat, you could buy a flash meter.
In reality is is a lot more complicated to explain than to perform once you get the concept. Good luck!
Visit my Nikonians gallery.
#2. "RE: Nikon D7000 - to use a Flash - SB28:" | In response to Reply # 0Leonard62 Nikonian since 15th Mar 2009Wed 09-Jan-13 11:33 PM
The SB-28 is a nice flash. You'll find it's easier to use in Auto mode rather than manual. Once you set the ISO and the f stop the flash does the rest since the sensor is on the front of the flash. The distance bar will tell you if the ISO and f stop is within the flash range. It's has a pretty wide auto range. As an example at ISO 400 and f5.6, everything within 3 1/2 feet and 30 feet will be perfectly exposed. You don't have to do any math. It works for me and the exposures are right on.
Visit my Nikonians gallery.
#3. "RE: Nikon D7000 - to use a Flash - SB28:" | In response to Reply # 2avm247 Charter MemberWed 09-Jan-13 11:58 PM
I have also used my SB28 in Auto flash mode, setting the ISO and the aperture all on the SB-28 with the office's D70s and my D700 (until I got my SB910). Exposures weren't always 100% but could easily be adjusted by chimping (reviewing the image in the camera) and adjusting accordingly. More often than not, I was pleased with the image.
Shooting RAW helped, too.
The Moderator Page and My Gallery
The important things in life are simple; the simple things are hard.