On vacation and over the past 2 days my D7000 has seemed to stop recognizing lenses. As of today no lenses are recognized, all get the EE error on all settings. Any ideas or has this been a known problem?
I tried a few lenses, like a Nikon 28mm, Nikon 18-135, and a Sigma 70-300.
#2. "RE: D7000 getting an EE errors on all lenses" In response to Reply # 0
East Point, GA, US
I had this issue a few months back and found the following on YouTube that resolved the issue for me. The video seems to be somewhat of a joke at first, but locking the aperture ring at the highest setting did the trick for me. I'm not sure however why this just started happening on my D7000 as I had never experienced it before. Maybe others can comment and provide more detail as to the actual cause (firmware bug maybe?).
#3. "RE: D7000 getting an EE errors on all lenses" In response to Reply # 2
Yes, I think that video was presented in a humourous way, because most members know that you need to set the lens' aperture ring - if it has one - to minimum (highest number) when using such lenses with modern Nikon cameras.
But... that's not the problem in this case, as Todd has already tried at least one lens (the 18-135mm) which is "G-type" and doesn't have an aperture ring
#4. "RE: D7000 getting an EE errors on all lenses" In response to Reply # 0 Sat 29-Dec-12 01:10 PM by Chris Platt
You may need service. However, your camera is a computer and every now and then it can get confused and may benefit from a reboot.
Have you tried turning it off, removing the battery for a few moments, then replacing the battery and turning it back on? (Page 299 of the user manual).
Thom Hogan provides a more exacting reboot routine in his Complete Guide to the Nikon D7000:
1. Turn the camera OFF. 2. If you're using battery power, remove the main battery. If you're using AC Power, unplug the adapter. 3. If possible, let the internal clock battery discharge (this normally takes days). 4. With the battery still removed turn the camera ON for several minutes. This step is to ensure any internal capacitors are discharged. 5. Turn the camera OFF. 6. Replace the batteries taken out in Step 2. 7. Turn the camera back On.
#5. "RE: D7000 getting an EE errors on all lenses" In response to Reply # 4 Sat 29-Dec-12 05:16 PM by Bravozulu
Los Angeles, US
Along with the above, don't overlook the simple measure of taking a piece of cotton saturated in alcohol to clean the lens contacts inside the F mount of the body, and on the mount end of each lens.
I do this a few times a year. Very low voltages run through those contacts, and drive focus, while communicating aperture, metering and distance data to the camera computer. So any electrical resistance is bound to throw things off.
#6. "RE: D7000 getting an EE errors on all lenses" In response to Reply # 5
Thanks for the ideas. I had run the ring through the range of aperture trying to get it to connect in case something was off. Did the several time on the 28 and 180 lenses. I had removed batteries and even tried a different battery.
I will swab when I get home. MY concern is I need this for a big work trip starting Jan 7. I will likely book a rental as a backup.
#7. "RE: D7000 getting an EE errors on all lenses" In response to Reply # 6
St Petersburg, RU
I imagine you tried the 2 button reset as the first resort but it does not sound good. The contacts are spring loaded on the lens side, so inspect them closely to see if the lens/mount contacts are at the proper height. As a general rule, contacts should not be "cleaned" with any solvent that could remove the film residue on the contacts that helps prevent oxidation. The only "dirt" that contacts need maintenance for is the naturally developing oxidation. It is a good idea to use a tiny amount of a good de-oxidizing agent on connectors once a year or so. The standard of the electronics industry is Caig Laboratories D-5 DeOxit but there are a number of them using the licensed formula from the first one named R-5 Cramolin. That is still available in Europe, as well as CRC 60. In the US, Caig products are used by most recording studios and broadcast for oxidation removal. Alcohol and anything labeled contact cleaner is probably too drying which increases the rate of oxidation. Some recommend a pencil eraser but that is one of the very worst ways of attempting to clean contacts. The contact might look shiny but its resistance increases because of the tiny scratch marks left in the mating surfaces, leaving more surface area to oxidize and less are for mating with its contact mate. I really doubt that contacts are staying consistently open for you, with 2 lenses, it is likely something less user serviceable. Stan St Petersburg Russia
#8. "RE: D7000 getting an EE errors on all lenses" In response to Reply # 7
The two button reset didn't do anything either. I am really not a fan of messing with the contacts so I was going to take it in for a cleaning anyways. I may still do that and get there thoughts, or just send it to Nikon for repair.
#10. "RE: D7000 getting an EE errors on all lenses" In response to Reply # 9
The repair shop was closed today so I tried a lens again. I think it is interesting that the focus dot in the lower left of the viewfinder works fine. So since something is working that keep me optimistic it is only something with the sensor/electroinics/ for the aperture hook up.
#12. "RE: D7000 getting an EE errors on all lenses" In response to Reply # 11
Got the camera back today. Was told the PCB unit went bad and that there was nothing I could have done to cause it. This irks me. The said it was just electronics and this was part of the motherboard. Another comment was there are so much electronics inside things go bad. Again this was an authorized Nikon Warranty repair center, though I am out of warranty.
72k shots, under 2 years and a $225 repair, plus $180 to rent a body in the meantime.
I am home testing it and the autofocus doesn't seem to want to work but will play with some more lenses.